Z Microsystems 21 Manual de usuario descargar pdf (Pagina 9)

927-0045UM REV B Issued 02/12

INSTALLATION

WARNING: Max Screw Depth 3/8”

Hardware exceeding max screw depth could

damage the display.

NOTE: Refer to the schematics on the previous

pages for your respective display size for visual

afrmation and mounting rail orientation.

NOTE: Mounting rails are equipped with guide

pins to assist with spacing and nal installation of

display to mounting assembly.

*GUIDE PIN - The Guide Pins are small

cylinder shaped metal rods that protrude from

the Mounting Rails to provide support and

reference guide when attaching the display to

the mount.

Installation Instructions for Static and Hinged Mounting Systems

2.2.1 Static Mount Installation

For help with installation follow these steps and refer to the schematic for your 17”, 21”, or 24” IDS

Step 1 - Clear a safe space to work and locate hardware & mounting rails

The rst step in mounting the IDS display is clearing a safe space to rest the monitor, screen side down

and collecting the parts and hardware you will need. After laying the monitor screen-down within the

the workspace prepared, locate the two mounting rails that have been provided with the IDS display

unit. These will serve as a harness for the display and the rails that will be secured directly to the mount

assembly where the monitor will rest.

Step 2 - Attach the Mounting Rails to the IDS

With the monitor, mounting rails, and hardware, position the rails so that the Guide Pins* face the

installer, and away from the IDS. With this orientation, attach the two mounting rails to the back side

of the unit using the provided hardware; or fasteners that match specications. The nuts and screws

should be tightened nger-tight. When both of the rails are rmly secured to the IDS display, proceed to

the next step.

Test - Be sure that mounting rails are securely fastened to the display before lifting the unit.

Step 3 - Lift the IDS into postion and Prepare to Mount

Now that the mounting rails are securely fastened to the IDS, the monitor is prepared to be mounted

to the desired position on a mount assembly. With the aid of a second person for assistance, lift the

IDS into place. With the aid of another installer and the guide pins, guide the monitor into place on the

mounting assembly.

Step 4 - Attach the Harnessed IDS to Mount

Securely attach the monitor, with mounting rails installed, to the chassis of the mount assembly using

the appropriate washers and screws as depicted in the schematic diagram. Make any necessary height

adjustments as needed and ensure that the display is securely installed and all hardware is nger-tight.

Step 5 - Proceed Connections & Setup

Be sure that the video ports and power jack on the back of the monitor have not been obstructed.

You have succesfully mounted the IDS and are now ready to setup and operate the display. Continue to

the next section.

If you have further questions regarding mounting, please refer to the troubleshooting or FAQ sections in

this manual for further assistance.

2.2.2 Hinged Mount Installation

The installation for a hinged IDS mount follows the same steps as the instructions above for the static

mount installation. The major three differences are: the larger hinged mounting rail, an increased

number of fastening locations for additional support with the hinged mounting feature, and different

hardware used for attachment.

The hinged mounting rail comes equipped with a sturdy hinge assembly and braided metal safety leash.

It provides the same easy installation experience as the static rails, with guide pins for installation and

convenient cable management built right in.

Static Rail Mount Parts & Hardware

• 2 Mounting Rails

• 4 x 01-92381, 4 x 01-92382 (Washers)

• 4 x 01-92619 (Screws)

• 4 or 8 01-91689 (Depending on Monitor, refer

to schematic)

Hinged Rail Mount Parts & Hardware

• 2 x Mounting Rails (1 Static + 1 Hinged)

• 4 x 01-92381, 4 x 01-91872 (Washers)

• 4 x 01-92619, 4 x 01-92869 (Screws)

• 4 or 8 01-91689 (Depending on Monitor, refer

to schematic)

2.2 Installation Walkthrough

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 27 28

Comentarios a estos manuales

Sin comentarios

Z Microsystems 21 Manual de usuario Pagina 9

Comentarios a estos manuales